I would start with a simple fix of the crank angle position sensor. The sensor system consists of a rotating part, typically a disc, as well as a static part, the actual sensor. I see it runs across the engine. Even when the ground connection looks clean, there can be a thin film of rust on the surface. Check the wire in the illustration.
In such cases you will want to check for a heat sensitive condition. Check after engine is warmed up suffi- ciently. Check it out and post back with what you find. This test may indicate a loose or poor electrical connection. Try to avoid direct skin contact with used oil. Voltage should be measured with a voltmeter. Heres the thing i have a 2003 nissan sentra se-r spec v.
It is this level of detail, along with hundreds of photos and illustrations, that guide the reader through each service and repair procedure. I have replaced the computer and crank and cam sensors. Is it possible to show me in the picture or tell me where the end part of the connector is at? Outer Socket Lock Nut : 59 - 78 N-m 6. If there is a trace of tube bulging left on the old rubber hose, align rubber hose at that position. Assembly, inspection and adjustment procedures for the complicated units such as the automatic tran- saxle or transmission, etc. The change in the magnetic field cause the voltage from the sensor to change.
Hopefully this is the fix and only problem. Limit value:The maximum or minimum limit value that should not be exceeded at inspection and adjust- ment. No part of this Service Manual may be reproduced or stored in a retrieval system, or transmitted in any form, or by any means, electronic, mechanical, photo-copying, recording or otherwise, without the prior written permission of Nissan North America, Inc. The changing gap causes the magnetic field near the sensor to change. To determine if an electrical component is heat sensitive, heat the component with a heat gun or equivalent.
Sealing point Checking point Always replace after every disassembly. This lighting up indicates that the anti-theft is not functioning, so prompt service is required. The rear seats can allow for adults, and all of sitting positions provide excellent breathing place. If tube is equipped with hose stopper, insert rubber hose into tube until it butts up against hose stopper. Static electricity may damage internal electronic components.
Using a fuel other than that specified could adversely affect the emission control devices and systems, and could also affect the warranty coverage validity. Brake Unit: mm in Total toe-in Distance A - B mm in Minimum 1 0. Put probes at the load side of fuse terminal and a known good ground. Unless otherwise indicated, use recommended multi-purpose grease. Do not remove the radiator cap when the engine is hot. The target for the current-technology model would be to eradicate the entry-stage look, to design a car featuring its own character which happens to remain in the proper price range for a lot of men and women.
Then you will be able to use the appropriate equipment and follow the correct test procedure. Using the wiring diagrams inspect the wiring for continuity. In such cases the incident could be caused by water intru- sion on an electrical part. Hey Soccer you may want to post this in the correct forum. The step by step voltage drop test can identify a component or wire with too much resistance. Service History and if any After Market Accessories have been installed. Do not smoke while working on the vehicle.
This unwanted resistance can change the way a circuit works. The first is to arrange for the owner to leave his car overnight. If multiple wires are cased in one eyelet make sure no ground wires have excess wire insulation. Sounds like your car is in limp mode. When it is connected with a diagnostic connector equipped on the vehicle side, it will communicate with the control unit equipped in the vehicle and then enable various kinds of diagnostic tests. Repeat step 1 and 2 again.
Spare tire, jack, hand tools and mats in designated positions. A poor or corroded ground can easily affect the circuit. The second method is to put the suspect component into a freezer long enough for any water to freeze. If in doubt, contact the local authority for advice on disposal facilities. This standard is applicable to bolts having the following marks embossed on the bolt head. Special care should be taken when handling any inflammable or poisonous materials, such as gasoline, refriger- ant gas, etc. Little or no resistance will indicate that portion of the circuit has good continuity.
Voltage Drop Tests Voltage drop tests are often used to find components or circuits which have excessive resistance. Apply positive voltage from battery with fuse directly to components. This may cause serious and expensive damage to the transaxle. Disconnect the negative battery terminal. Common issue and gives the same symptoms you described.