After some time fiddling around under the glove box, I found it! Remove the glove box and the glove box frame damping screws on the sides and two screws underneath. Remove the blower motor from the dashboard. Now, the housing can be removed by carefully pulling back on the dash while guiding the housing assembly down and to the left. You have to remove the console and that entails taking the off the shift knob automatics beware - the spring will go flying. Remove the screws and pop the cover off and now you should be looking at the ac blower motor as well. Remove the inner handle A. What could be the problem? First, remove the metal band securing the blowermotor housing and the heater core housing together.
Power window models: Remove the pull pocket panel A. Without a new motor or resistor, your Accord is not capable of keeping you and your passengers cool and comfortable during your road-trips in the hot weather. In the case that it still has those bolts, un torque the steak nut on the axle, you must pop upper and lower ball joints as well as the tie rod. This article applies to the Honda Accord 1990-2002. Look to there upper tube from radiator is make fast to enginebody.
The blower fit perfectly and blows really strong. Pry out the old gasket and clean the surface of the head where the gasket will touch it. Just check them by hand and make sure they're as tight as I want them to be and not tighter. Hope this helps On retractable headlight models raise the headlightsDisconnect the neagative battery cableRemove the retaining screws taking care not to disturb the adjustment screwsRemove the retainer and pull the headlight out enough to allow the connector to be unplugedRemove the headlightTo install the headlight plug the connector in place the headlight in position and install the retainer screws tighten the screws securleyPlace the headlight bezel in position and install the retaining screws. Half the dashboard has to be taken apart, the glove box removed, loads of bolts and screws from inside the dash which can only be accessed when laying upside down on the passenger floor. My specialties are body wiring, electrical, brakes, and air conditioning. The problem is with the fan I turn the thermostat up to turn the furnace on.
Seventh, pull the carpet back on the passenger side and remove thefour nuts securing the computer to the floor board and swing it out tothe left. Open the glove compartment and remove the one screw on the right-hand… This is fairly simple, although the position is a little awkward. The included plug adapter was needed, and worked perfectly. To remove the fan, here's your lead back in here. I'll take those fasteners out. The motor cap that came off contained both brushes and it was obvious both brushes were worn totally away at 150,000 miles. It just means the bearings are starting to wear down.
To install a new ac blower motor for a 1992 Honda Accord, just reverse the removal directions. Installation is reverse of above. My specialties are body wiring, electrical, brakes, and air conditioning. A fluid leak can damage the blower motor assembly, and keep it from working. . This job has been too much of a pain in that well known spot to try rebuilding the motor.
After all that, plug your antenna adapter into the back… Verify that the engine is not running, set the parking brake, and shift into neutral. If you are replacing the blower motor itself, or either of the blower fan wheels, remove the motor, remove the retaining clip s and remove the fan wheel s. Just beneath the dash you should see a plastic cover held in place by 2 screws. Take care not to scratch the door panel. The first time you do it, it'll probably be a little difficult, but you just press it and pull it down.
Take care not to scratch the door panel. The blower motor is usually removed for replacement or to clean the blower motor's fan cage. Release the clips A, B that hold the door panel C with a commercially available trim pad remover D , then remove the door panel by pulling it upward. Once the bolts are removed, lower the ac blower motor down from beneath the dashboard and that is it. Let the damper dangle, so that it isn't in the way. Take the old bulb out, put the new one in, push the bulb inside the holder in the correct position, lock the coupling back on and your good to go.
So why not take the unique route, and install a supercharger? It may be necessary to manipulate the jack somewhat once things are unbolted. So find out how to do that with this helpful guide. Submitted 2018-09-03 By William From Undisclosed This was a great alternative to the Honda part. It is 2 or 3 screws there. Get the blower motor inspected.
It took me about one hour. Hope this is at least helpful. When re-installing reiverse the process. The wheels, from heat and cold over many years, become very set on the blower rod. I have run temporay feed wires from the battery to the motor. It doesn't matter if you want cold or hot air, nothing happens. If you can not press the tab down by hand, carefully use a flat-head screwdriver to push it down.