Sometimes also a no disc symptoms can be caused by disc table spindle platter height set too low or too high. Go to a hardware store and get a compatible fuse and swap it out with the broken fuse. If you can't, don't force it. Humphrey- Sure: if tested and found to be okay. The material on this site may not be reproduced, distributed, transmitted, cached or otherwise used, except with the prior written permission of Advance Local.
I hope you like this article and answers by Humphrey Kimathi and if you wish to visit his blog you can log on to Recommendation:. If you spin the disc with your hand it should rotate freely. If you can't find an exact match, go for the slightly smaller size. Our employees are always knowledgeable about what to do and what works best. If you have any questions regarding this fix, please feel free to post them in the comments. First, apologies for the video quality; this was done off-the-cuff without much preparation. If the next size up is too large, try flexing the O-ring a bit to loosen it up.
Remove the screws from the unit by locating the screw holes and taking out the screws with the appropriate screwdriver. If the player is having trouble loading or reading discs, the problem is almost always mechanical. If you have installed a flip down monitor in your vehicle or if your car came with one installed , there may come a time when the unit does not function the way it should. There are also, I'm sure, videos on YouTube demonstrating this, however I'd strongly recommend following the service manual and only using YouTube video's as supplements. If the pickup moves to the inner area smoothly and after reaching the inner lane the lens start moving up and down emitting red light then most probably the lens is okay. I waited 12, but it might be advisable to wait even longer.
The highly trained staff can help you in each step along the way and can help you decide exactly what works best for you. Instead, use a small flat-blade screwdriver to press against the cogs on one of the gears beneath the tray. If that doesn't work, don't give up yet. Another option is to simply remove the fuse for the device that is no longer being used in the vehicle. While you may be able to see something on the screen, there may be moving horizontal or vertical lines that cause the picture of the display to be unclear or blurry. Also, I used a syringe with a screw-on needle- I found this was necessary as the cement was too viscous to draw in through the needle itself. As you push the screwdriver to rotate the gears, the tray should start to slide open.
Ensure that all the inner mechanisms stay in place. Therefore if a technician understands one model pretty well then you will have no problem when a customer brings a different model to you shop. Everything from the stereo to the engine is packed with various electronics which were unthinkable back then. If a specific disk won't read at all: look for heavy scratches towards the center and emphasize polishing those optical discs read from the center out, and the laser can't find track 0 to start reading the disc. Of course, you could try to buy a new rubber belt online -- if you can find one.
If a gear belt is loose, place the belt back on the gear securely. With our great customer service, we offer opinions and honest diagnosis, and we won't proceed with anything until we explain to you exactly what we are doing. Placing the syringe needle between the rubber and the axle without something like a screwdriver in place creates the risk of either puncturing the rubber, or breaking the needle off. The motor turns on, but with no belt, it can't turn the gears that operate the tray. .
Perhaps the display is not clear or there is no display at all. Now open up the machine and go to the pickup, if the pickup is on the inner area push it slowly and carefully to the outer zone with power off. This will help the tray glide more easily. If you can get the tray open, leave it partially open. Disc Skips, Doesn't Play Smoothly Any bumps or vibrations can affect the disc. Reattach the cover you do remember which screws go where, right? You want to check for shorts in the power supply cord as well by jiggling the cord around and seeing if the device turns on and off.
There can be a number of different problems that could go wrong, but most of them have pretty simple solutions that can be done relatively quickly and with little monetary investment. With the screwdriver still in place, I injected the cement slowly while drawing the needle out. But even though the cost of the belt itself wouldn't be much, the cost of shipping would hardly make it worth your while. If the monitor was installed by the car manufacturer, the problem is probably related to a fuse. Second, using a syringe allows you to inject the cement into the first half inch of the axle, not just the outside area.